Anritsu S332C Especificaciones descargar pdf (Pagina 6)

4. RETURN LOSS VERIFICATION

The following test can be used to verify the accuracy

of return loss measurements. Measurement calibra

-

tion of the Site Master is required for this test.

a. Equipment Required:

·

20 dB offset, Anritsu SC5270

·

6 dB offset, Anritsu SC5237

·

Open/Short, Anritsu 22N50

·

50 Ohm Termination,

Anritsu 28N50-2 or SM/PL

b. Procedure:

1. Press and hold the

ESCAPE/CLEAR key,

then press the

ON/OFF key to turn on the

Site Master. (This sets the instrument to

the factory preset state.)

NOTE

Before continuing, allow a five minute warm

up for the internal circuitry to stabilize.

2. Press the

MODE key.

3. Use the Up/Down arrow key to highlight

RETURN LOSS, then press ENTER.

4. Press the

START CAL key.

5. Follow the instructions on the screen to

perform a calibration using a 22N50

Open/Short and 28N50-2 or SM/PL Ter-

mination.

6. Connect the 20 dB offset to the Refl Test

Port and verify that the reading is 20 dB

± 1.7 dB.

7. Connect the 6 dB offset to the Refl Test

Port and verify that the reading is 6 dB

± 1.2 dB.

5. SPECTRUM ANALYZER FREQUENCY

ACCURACY

The following test can be used to verify the CW fre

-

quency accuracy of the Site Master Spectrum Ana

-

lyzer.

a. Equipment Required:

·

Anritsu MG3692A Synthesized Signal

Source, with options 4 and 15A

·

10 MHz Reference Standard

b. Procedure:

1. Connect the 10 MHz reference source to

the Anritsu MG3692A Synthesized Sig

-

nal Source.

2. Connect the output of the source to the

RF Input of the Site Master.

3. Connect the external power supply

(Anritsu part number 40-115) to the Site

Master.

4. Press and hold the

ESCAPE/CLEAR key,

then press the

ON/OFF key to turn on the

Site Master. (This sets the instrument to

the factory preset state.)

5. Turn on the 10 MHz reference source

and the Anritsu MG3692A Synthesized

Signal Source.

6. Set the MG3692A output to 1000 MHz

CW for the S114C (2000 MHz CW for the

S332C), with an RF output level of 0

dBm.

NOTE

Before continuing, allow a 30-minute warm up

for the internal circuitry to stabilize.

7. On the Site Master, press the

MODE key.

Use the up/down arrow key to highlight

SPECTRUM ANALYZER and press ENTER

to select spectrum analyzer mode.

8. Press the

AMPLITUDE key and the REF

LEVEL

soft key.

9. Enter 20 and press the

ENTER key to set

the Reference Level to 20 dBm.

10. Press the

FREQ/DIST key and the CENTER

soft key.

11. For the S114C, enter

1000 and press the

MHz soft key to set the center frequency

to 1000 MHz. For the S332C, enter

2000

and press the MHz soft key to set the cen

-

ter frequency to 2000 MHz.

12. Press the

SPAN soft key and enter 50.

Press the

kHz soft key to set the span to

50 kHz.

13. Press the SWEEP key.

14. Press the

RBW soft key and then the

MANUAL soft key. Use the Up/down arrow

key to select

10 kHz. Press ENTER to set

the resolution bandwidth to 10 kHz and

press the

BACK soft key.

2 Site Master S114C/S332C MM

1 2 3 4 5 6 7 8 9 10 11 ... 27 28

Comentarios a estos manuales

Sin comentarios