Anritsu Site Master S331D Guía de usuario Pagina 32
- Pagina / 102
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
MARKER
Choosing MARKER in cable and antenna analyzer freq and dist mode causes
the soft keys, below, to be displayed and the corresponding values to be shown
in the message area. Selected frequency marker or distance marker locations
may be changed using the keypad or Up/Down arrow key.
q
M1 — Selects the M1 marker parameter and opens the M1 marker second
level menu.
q
On/Off — Turns the selected marker on or off.
q
Edit — Opens the selected marker parameter for data entry. Press
ENTER when data entry is complete or ESCAPE to restore the previous
value.
q
Marker To Peak — Places the selected marker at the frequency or dis-
tance with the maximum amplitude value.
q
Marker To Valley — Places the selected marker at the frequency or dis-
tance with the minimum amplitude value.
q
Back — Returns to the Main Markers Menu.
q
M2 through M4 — Selects the marker parameter and opens the marker second
level menu.
q
On/Off — Turns the selected marker on or off.
q
Edit — Opens the selected marker parameter for data entry. Press
ENTER when data entry is complete or ESCAPE to restore the previous
value.
q
Delta (Mx-M1) — Displays delta amplitude value as well as delta fre-
quency or distance for the selected marker with respect to the M1 marker.
q
Marker To Peak — Places the selected marker at the frequency or dis-
tance with the maximum amplitude value.
q
Marker To Valley — Places the selected marker at the frequency or dis-
tance with the minimum amplitude value.
q
Back — Returns to the Main Markers Menu.
q
All Off — Turns all markers off.
q
More — Opens the continuation of the Marker Menus.
q
M5 — Selects the M5 marker parameter and opens the M5 second level
menu.
q
On/Off — Turns the selected marker on or off.
q
Edit — Opens the selected marker parameter for data entry. Press
ENTER when data entry is complete or ESCAPE to restore the pre-
vious value.
q
Peak Between M1 & M2 — Places the selected marker at the fre-
quency or distance with the maximum amplitude value between
marker M1 and marker M2.
q
Valley Between M1 & M2 — Places the selected marker at the fre-
quency or distance with the minimum amplitude value between
marker M1 and marker M2.
q
Back — Returns to the Main Markers Menu.
2-12
Chapter 2 Functions and Operations
- Site Masterä 1
- WARRANTY 2
- LIMITATION OF WARRANTY 2
- TRADEMARK ACKNOWLEDGMENTS 2
- S331D, MS2711D 3
- Table of Contents 5
- Chapter 1 9
- General Information 9
- Standard Accessories 10
- External Detectors 11
- Optional Accessories 12
- Chapter 1 General Information 13
- Performance Specifications 15
- Preventive Maintenance 18
- Calibration 18
- ESD Precautions 19
- Anritsu Service Centers 19
- Mode References 19
- Annual Verification 19
- Chapter 2 21
- Functions and Operations 21
- Display Overview 23
- Front Panel Overview 24
- Function Hard Keys 25
- Keypad Hard Keys 26
- Save Setup selection box 27
- Soft Keys 28
- MODE=DTF: 29
- SOFTKEYS: 29
- FREQ/DIST 29
- AMPLITUDE 29
- MEAS/DISP 29
- Self Test 38
- Error Messages 39
- Range Error Messages 40
- InstaCal Error Messages 41
- General Error Messages 42
- Battery Information 43
- Battery Life 45
- Important Battery Information 46
- Chapter 3 47
- Getting Started 47
- Selecting the Frequency 48
- Calibration Verification 49
- CALIBRATION 50
- InstaCal Module Verification 51
- Auto Scale 54
- Amplitude Scale 54
- Custom, for additional ca 55
- All Modes 56
- Changing the Units 57
- Changing the Language 57
- Adjusting Markers 57
- Adjusting Limits 58
- Printing 60
- Using the Soft Carrying Case 61
- Chapter 4 63
- Cable and Antenna 63
- Analyzer Measurements 63
- CW Mode/RF Immunity 65
- Cable Loss Measurement 67
- Resolution 70
- MODE key 71
- Chapter 5 73
- Power Monitor Mode 73
- Chapter 6 75
- High Accuracy Power Meter 75
- Power Measurement 76
- Rel soft key. The 78
- Chapter 7 79
- Handheld Software Tools 79
- System Requirements 80
- Installation 80
- Communication Port Setting 81
- Interface Cable Installation 82
- Using Handheld Software Tools 83
- Plot Properties 84
- Trace Overlay or Plot Overlay 85
- Saving Traces 85
- Creating a Database 86
- Printing Formats 86
- Cable List 87
- Creating a Custom Cable List 87
- Uploading a Cable List 87
- DTF Plots 87
- Smith Chart 88
- Signal Standards Editor 89
- Signal Standards Reports 90
- Chapter 8 91
- Master Software Tools 91
- Minimum System Requirements 94
- Appendix A 95
- Windowing 95
- Appendix A Windowing 96
- ....................3-6 99
Relacionado con productos y manuales para Redes Anritsu Site Master S331D
Redes Anritsu Site Master S332D Guía de usuario
(112 paginas)
(112 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.041 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales